Chrysler 300M Enthusiasts Club
  • Steering rack check?

  • Repair Questions and Answers.
Membership Banner

Repair Questions and Answers.

Moderator: Moderators

 #395547  by JohnnyP
At Rock Auto, the Gabriel "Ultra Ready Mount" are in stock, left and right are $147.79 each. For KYB's, they are only showing the left one in stock at $140.79.
Welp, I guess the Monroe's are going back. :)
 #395549  by rustybronco
Dale: Thanks for details on a strut rebuild. But I'm in a condo with a small garage, no real place to do front end work.
All it requires is a floor jack, a few tools and a spot in the driveway. Compressing the spring and swapping parts is the only difference between buying quick struts and re-shocking yours. All the rest is the same. The difference in cost you'll need to figure out which works best for your situation.. ... 63262.html I use an O.E.M. tools strut compressor. These look the same. ... 6BNT&psc=1

If you aren't allowed to work on vehicle in your driveway may I suggest moving?
 #395550  by rustybronco ... R9Kv_ereYw

KYB struts are $55.79 ea

KYB upper insulators are $8.74 ea
KYB lower insulators are $9.82 ea

Monroe upper insulators are $4.77 ea
Monroe lower insulators are $4.71 ea

plus shipping.
User avatar
 #395562  by In-trepid
I use the KYB struts and Monroe insulators on all four struts. On the rears, I use either the stock strut mount that is currently on the car or any one of the aftermarket mounts as the rear strut mounts are stationary pieces and unless they are stretched, torn, or mushy they are probably still good. Both are the same. On the fronts, I use only Mopar strut mounts and bearings. The mounts are side specific, and the aftermarket seems to treat both sides as the same. Never an issue with the Mopar front strut mounts and bearings. After reading numerous posts and horror stories on this and other forums about either aftermarket mounts and/or bearings by third party manufacturers, I will always spend the extra money for the Mopar pieces. It guarantees that you only have to do it once!
 #395563  by rustybronco
I received the KYB SM5167 this afternoon. She's indexed close to the proper right front upper mount plate. It's off by about 30 degrees. Instead of pointing to the right of the closest stud to the square hole at the 10 o'clock position, it aims directly to the edge of the square hole closest to the stud. (10:15?)

Made in India just like the NAPA right upper mount.

I have pictures of the mount.
User avatar
 #395564  by FIREM
Step by step with pictures and detailed information about struts, mounts, bearings and isolators here :viewtopic.php?t=19430
 #395568  by JohnnyP
Thank you everyone for all your help. I'll have the struts rebuilt at a later time. For now I'm just going to have inner and outer tie rods, links, and strut rod bushings bushings replaced by a local shop.

The garage in my condo is too small to do any work. Originally it was an open four bay garage with separate doors, serving four residences, but I enclosed mine with a wall on both sides.
 #395737  by JohnnyP
I had a local shop do the suspension work. They replaced inner and outer tie rods, control arms, links, strut rod bushings, and replaced the strut assemblies with KYB's. He wanted to use Monroe but that was a no go. They also did a four wheel alignment, giving me data sheets showing the readings before and after.

There is a little torque steer, not as bad as before the work. It wants to push to the left when accelerating, then goes to the right when I let off.

Also, there is about an inch of play in the steering wheel when coasting, and about half an inch when accelerating. It wanders as the camber in the road changes, so you have to pay attention. My 2000 Intrepid ES has no torque steer and the play in the steering wheel is half an inch, accelerating or coasting.

I guess the only thing left is the rack? I bought one, was about to send it back. Any thing else it could be?
 #395738  by rustybronco
ImageI'm wondering if the KYB upper strut mounts will have something to do with the torque steer. The one I have is on a drastic angle.
How are the steering gear bushings? Cradle mounts?
You do not have the required permissions to view the files attached to this post.
User avatar
 #395745  by TrepKing95
Post your alignment sheets, they could have clues about the Torque Steer. (Just because the sheet is "green" doesn't necessarily mean its good! I noticed a lot of Torque Steer in my Intrepid when the motor mounts failed, causing the C/V Axle geometry to go out of whack. I wonder if that's part of the issue.
 #395750  by JohnnyP
I think the steering wheel play is related to the torque steer. The play goes away when I am on the throttle. Even light throttle.

Here are the before and after alignment data sheets.
You do not have the required permissions to view the files attached to this post.